HYRITE LEDMM-W320-PH-P65 | Mini IP67 LED Module 6500K

With compact dimensions of 27.2 × 9.6 × 8.07 mm and 70 mm module center spacing, the LEDMM-W320-PH-P65 is designed for flexible placement in small channel letters, advertising signs and localized illuminated displays.

160° Wide-Beam Micro-Prism Optical Technology

The micro-prism optical design provides a 160° beam angle, helping distribute light over a wider area for smoother illumination in channel letters and advertising light boxes.

Recommended Depth-to-Spacing Ratio

D : P = 1 : 2

D = Installation depth

P = Module center-to-center spacing

A depth-to-spacing ratio of 1:2 means that the module spacing is twice the installation depth. This is a recommended optical ratio based on laboratory reference conditions. The actual module layout should be verified according to the sign structure and required illumination.

Important: DC12V is the default configuration and DC24V is optional. Use constant-voltage power supplies only. Do not connect the modules to constant-current power supplies. The standard string contains 20 modules, while the maximum connected quantity is 50 modules per chain. The total number of modules connected to one power supply must also comply with the power supply rating and wiring design.

Installation Recommendations

1. Clean the inside surface of the sign or light box using a suitable surface cleaner and remove dust, oil and debris.
2. Remove the protective layer from the rear adhesive tape and mount the modules. Use suitable pan-head tapping screws where required.
3. Drill wiring holes at the bottom or side of the sign box and use suitable grommets to protect the wires.
4. Connect the modules in parallel using suitable waterproof connectors. Do not exceed 50 modules per chain.
5. Cap all unused wires. Do not loop the module chain to create a closed circuit.
6. Run the DC power supply wires to each channel letter or light box and connect them to the module-chain input. Match the power supply voltage to the selected module rating.
7. Observe correct polarity. The red/white wire is positive (+), and the white wire is negative (-). Check the actual product markings before connection.
8. Complete the AC power connection to the power supply only after finishing the DC-side wiring.

Storage & Maintenance

• Disconnect power and allow all modules to cool completely before maintenance.
• Do not pull on the wires when removing modules.
• Store in a cool, dry place away from direct sunlight, excessive heat, pressure, vibration and corrosive or flammable gases.
• Do not clean with thinner, benzene or other volatile solvents.
• Keep modules away from sulfur-containing materials or gases.
• Install in a well-ventilated area and keep the ambient temperature below +60°C.
• Provide adequate ventilation and drainage for signboard installations.
• Do not use metal cable clamps that may damage cable insulation.
• After switching off the power supply, wait at least 5 minutes before connecting modules to avoid damage from residual voltage.
• Do not excessively bend, twist or pull the power cables.

Installation & Operating Conditions

• Installation must be performed by qualified personnel in accordance with applicable electrical safety requirements.
• Do not exceed the specified ratings of the modules or power supply.
• Keep modules away from heat sources. Do not cover them with cloth, paper or other materials that restrict heat dissipation.
• Avoid excessive vibration, impact, airborne particles and corrosive or flammable gases.
• Do not handle power plugs with wet hands. Keep cables away from heating equipment.
• Do not modify the modules or mix them with other LED module types.
• Protect modules from direct sunlight and dripping or running water.
• Follow the power supply manufacturer's grounding requirements, particularly in humid locations.
• Operating ambient temperature: -20°C to +60°C.

OEM Logo & Packaging Customization

OEM customization is available for logos and packaging. Contact HYRITE to discuss your branding and project requirements.

Looking for Mini LED Modules for Your Signage Projects?

Tell us about your signage application, required voltage and estimated quantity. Our team will help you identify a suitable LED module configuration for your project.

Technical support | Product specifications | Pricing | OEM customization

HYRITE Lighting Co. | Professional LED Module & LED Power Supply Manufacturer Since 1993